ULUSLARARASI YAYINLAR

Kelime Arama:


  SCI, SCI-E, SCOPUS MAKALE
1. Kuzu, C., Germak, A., Menelao, F., ?tibler, A., Genta, G., Loewit, M., Borovsk?, J., Maculott, G., Hiti, M., Prato, A., Pelit, E., Fidelus, J., Apostol, T., Ali?i?, ?., Faki?, B., Reinstädt, P., Turotti, F., Affri, R., Muminovic, B., Ali?, A. "Traceability for Indentation Measurements in Brinell-Vickers-Knoop Hardness", Measurement : Sensor, -:- (2025) : Article number 101453
2. Dogan, C., Tunaci, S., Jarbua, S.B., Alqarni, S. "1 kN·m binary dead weight torque standard machine at SASO / NMCC", Measurement : Sensor, -:DOI 10.1016/j.measen.2024.101383 (2025) : Article number 101383
3. Kuzu, C., Jurbua, S.B. "Development of Transfer Standards for Traceability of Hardness Diamond Indenter Calibration Systems", Measurement : Sensor, -:Development of transfer standards for traceability of hardness diamond indenter calibration systems (2024) : Article number 101447
4. Nevcanoglu, A., Aydemir, B., Gulsoy, H.O. "The Effect of Aging Heat Treatments on Room and High-Temperature Wear Performance of the Inconel 718™ Manufactured by Laser Powder Bed Fusion", Arabian Journal for Science and Engineering, -:DOI 10.1007/s13369-024-09523-3 (2024) : 1-19
5. Kuzu, C., Kazmanli, K. "Realization of Martens Hardness Method in Macro Range with High Accuracy Force and Indentation Depth", Acta Imeko, 13:1 (2024) : 1-7
6. Kacar, B., Aydemir, B. "A Review Study of Differences Between Alignment Verification Standards", MAPAN-Journal of Metrology Society of India , 1:1 (2022) : 1-10
7. Dizdar, H., Aydemir, B., Vatan, C. "Investigation of the Effect of Load Rate on Creep and Hysteresis Errors in Strain Gauge and Piezoelectric Force Transducer ", Measurement : Sensors, 22:August (2022) : Article number 100374
8. Sepetcioglu, H., Aydemir, B. "Short‐term Creep Experiments and Modeling on the Effect of Nano‑Sized Calcium Carbonate Particles and Applied Stress on Nonlinear Viscoelastic Behavior of High‑Density Polyethylene", Journal of Polymer Research, 29:4 (2022) : Article number 126
9. Germak, A., Kuzu, C., Origlia, C., Pelit, E., Menelao, F. "Result Analysis of EURAMET Brinell Comparison Between INRiM, UME and PTB (EURAMET.M.H–S2.A.B)", Measurement : Sensors, 18:DOI 10.1016/j.measen.2021.100251 (2021) : Article number 100251
10. Kuzu, C., Germak, A., Origlia, C., Pelit, E. "Result Analysis of EURAMET Vickers Comparison Between INRiM and UME (EURAMET.M.H-K1.b.c)", Measurement : Sensors, 18:https://doi.org/10.1016/j.measen.2021.100268 (2021) : Article number 100268
11. Dizdar, H., Aydemir, B., Vatan, C. "Establishment of Continuous Force Calibration System at TUBITAK UME Force Laboratory in Turkey", Measurement : Sensors, 18:https://doi.org/10.1016/j.measen.2021.100216 (2021) : Article number 100216
12. Aydemir, B. "Uncertainty Analysis in the Notch Impact Test, for Materials with Different Energy Levels", Acta Polytechnica Hungarica, 18:7 (2021) : 187-200
13. Germak, A., Kuzu, C., Menelao, F., Origlia, C., Pelit, E. "Euramet Supplementary Comparison Between INRiM, UME and PTB in Brinell Hardness Scales (HBW1/30 - HBW2.5/187.5)- Euramet.M.H-S2.a", Metrologia, 58:1A (2021) : Article number 07003
14. Germak, A., Kuzu, C., Origlia, C., Pelit, E. "EURAMET Key Comparison Between INRiM and UME in Vickers Hardness Scales (HV1 - HV30) - EURAMET.M.H-K1.b and c", Metrologia, 58:1A (2021) : Article number 07002
15. Germak, A., Kuzu, C., Origlia, C., Pelit, E. "EURAMET Supplementary Comparison Between INRIM and UME in Rockwell Hardness Scales (HRA - HRBW - HRC) - EURAMETMH-S1.a.b.c", Metrologia, 57:1A (2020) : 07018
16. Dlamini, S., Sibisi, M., Matosse, J., Aydemir, B., Vatan, C., Dizdar, H. "NMISA’S New 5 kN Deadweight Force Standard Machine", Acta IMEKO, 9:5 (2020) : 85-87
17. Kuzu, C., Pelit, E., Meral, I. "A New Design Of Rockwell-Brinell-Vickers Hardness Standard Machine at UME", Acta IMEKO, 9:5 (2020) : 230-234
18. Kuzu, C., Germak, A., Origlia, C., Pelit, E. "Preliminary Results of Euramet Rockwell Comparison Between INRIM and UME (Euramet.M.H-S1.A.B.C)", Acta IMEKO, 9:5 (2020) : 256-260
19. Kuzu, C., Pelit, E. "Design and Development of Hıgh Load Brinell Hardness Standard Machine at UME", Acta IMEKO, 9:5 (2020) : 226-229
20. Ahmedov, H., Korutlu, B., Orhan, R., Tuncel, O., Dogan, C. "Design of UME Kibble Balance-3", Conference on Precision Electromagnetic Measurements (CPEM 2020), Denver, 24-28 August 2020, 2020:DOI: 10.1109/CPEM49742.2020.9191798 (2020) : Article number 9191798
21. Sepet, H., Aydemir, B., Tarakcioglu, N. "Evaluation of Mechanical and Thermal Properties and Creep Behavior of Micro- and Nano-CaCO3 Particle-Filled HDPE Nano- and Microcomposites Produced in Large Scale", Polymer Bulletin, 77:7 (2020) : 3677-3695
22. Germak, A., Kuzu, C., Origlia, C., Pelit, E. "Euramet Supplementary Comparison Between INRIM and UME in Rockwell Hardness Scales (Hra-Hrbw-hrc)-Euramet.m.h-s1.a.b.c", Metrologia, 57:1A (2020) : Article number 07018
23. Dizdar, H., Aydemir, B., Vatan, C. "Investigation of Different Compression Apparatus Usage Effects in Calibration Process of Strain Cylinders", MAPAN - Journal of Metrology Society of India, 35:3 (2020) : 359-364
24. Aydemir, B., Vatan, C., Dizdar, H., Binown, A. "Bilateral Comparison on Force Standard Machines Between TUBITAK-UME and SASO-NMCC", Metrologia, 57:Technical Supplement 1A (2020) : Article number 07007
25. Aydemir, B., Vatan, C., Dizdar, H., Binown, A., Mitsas, C., Justice, B., Zarouni, M., Shehhi, K. "Comparison of Force Standard Machines in The Range of 100 kN and 1000 kN", Metrologia, 57:Technical Supplement 1A (2020) : Article number 07006
26. Sepet, H., Aydemir, B., Tarakcioglu, N. "Evaluation of Mechanical and Thermal Properties and Creep Behavior of Micro- and Nano-CaCO3 Particle-Filled HDPE Nano- and Microcomposites Produced in Large Scale", Polymer Bulletin, -:https://doi.org/10.1007/s00289-019-02922-9 (2019) : 1-19
27. Kuzu, C., Meral, I., Pelit, E. "Metrological Characterization of Hardness Indenter Calibration System (XXII World Congress of the International Measurement Confederation (IMEKO 2018))", Journal of Physics: Conference Series, 1065:6/Article number 062014 (2018) : 1-4
28. Aydemir, B., Vatan, C., Dizdar, H., Binown, A.A., Algamdi, H.A., Algamdi, M.S. "Comparison on Force Standard Machines between TÜBİTAK UME and SASO NMCC (XXII World Congress of the International Measurement Confederation (IMEKO 2018))", Journal of Physics: Conference Series, 1065:4/Article number 042038 (2018) : 1-5
29. Durgut, Y., Aydemir, B., Bagci, E., Aksahin, E., T. Ince, A. "Development of Dynamic Calibration Machine for Pressure (XXII World Congress of the International Measurement Confederation (IMEKO 2018))", Journal of Physics: Conference Series, 1065:16/Article number 162013 (2018) : 1-5
30. Yagmur, L., Aydemir, B. "A Comparative Study for Material Selection of Sensor Element Using Analytic Hierarchy Process", Mapan - Journal of Metrology Society of India, June:https://doi.org/10.1007/s (2018) : 1-10
31. Aydemir, B., Zeytin, H., Guven, G. "Investigation of Portevin-Le Chatelier Effect of Hot-Rolled Fe-13Mn-0.2C-1Al-1Si Twip Steel", Materiali in Tehnologije, 50:4 (2016) : 511-516
32. Aydemir, B., Zeytin, H.K., Guven, G. "Investigation of Portevin-le Chatelier Effect of Hot-Rolled Fe-13Mn-0.2C-1Al-1Si Twip Steel", Materials and Technology , 50:4 (2016) : 511-516
33. Kuzu, C., Pelit, E. "Interlaboratory Comparison in Calibration of Hardness Testing Machines in Turkey", 20th IMEKO World Congress Busan; South Korea; 9-14 September 2012, 2:- (2012) : 1483-1487
34. Kacmaz, S., Akcadag, U.Y., Aydemir, B. "Micro -Mass Standards and Short Time Instabilities", 20th IMEKO World Congress Busan; South Korea ; 9 -14 September 2012, 3:- (2012) : 1850-1851
35. Aydemir, B. "The Investigation of Mechanical Behavior of CaCO3 in Polyethylenes", KGK / Kautschuk, Gummi, Kunststoffe, 65:9 (2012) : 35-38
36. Akkoyunlu, O., Hazar, E.A. "Covering Stack of Layers Consisting of a Single Layer: Local Near-Surface Buckling Instability", Scientific Research and Essays, 7:32 (2012) : 2857-2867
37. Fank, S., Aydemir, B. "Calculation of Measurement Uncertainty for Cellulose Based Transformed Board Material in Tensile Testing", International Journal of Metrology and Quality Engineering, 3:2 (2012) : 15-18
38. Vincke, W., Zhimin, Z., Pusa, A., Averlant, P., Kumme, R., Germak, A., Ueda, K., Park, Y., Torres, J., Burke, B., Langmead, F., Fank, S., Knott, A., Bartel, T. "Final Report on Force Key Comparison CCM.F-K2.a and CCM.F-K2.b (50 kN and 100 kN)", Metrologia, 49:Technical Supplement 1A (2012) : 07002
39. Ortan, Y., Arslan, T., Aydemir, B. "A Comparative in Vitro Study of Frictional Resistance Between Lingual Brackets and Stainless Steel Archwires", European Journal of Orthodontics, 34:1 (2012) : 119-125
40. Engin, G., Aydemir, B., Gulsoy, H. "Injection Molding of Micro-Porous Titanium Alloy with Space Holder Technique", Rare Metals, 30:6 (2011) : 565-571
41. Dusunceli, N., Aydemir, B. "The Effects of Loading History and Manufacturing Methods on the Mechanical Behavior of High-Density Polyethylene", Journal of Elastomers and Plastics, 43:5 (2011) : 451-468
42. Yagmur, L., Duygulu, O., Aydemir, B. "Investigation of Metastable yprecipitate Using HRTEM in Aged Cu-Be Alloy", Materials Science and Engineering: A, 528:12 (2011) : 4147–4151
43. Dusunceli, N., Aydemir, B., Terzi, N. "Cyclic behavior of high density polyethylene (HDPE)", AIP Conference Proceedings, 1255:https://doi.org/10.1063/1.3455664 (2010) : 58-60
44. Gezer, H., Aydemir, B. "The Effect of the Wrapped Carbon Fiber Reinforced Polymer Material on Fir and Pine Woods", Materials and Design, 31:7 (2010) : 3564?3567
45. Aydemir, B., Yagmur, L., Fank, S. "Hysteresis Errors of Commonly Used Sensor Materials", Measurement, 43:6 (2010) : 792?796
46. Sayinsu, K., Isik, F., Sezen, S., Aydemir, B. "Effect of Blood and Saliva Contamination on Bond Strength of Brackets Bonded With a Protective Liquid Polish and a Light-Cured Adhesive", American Journal of Orthodontics and Dentofacial Orthopedics, 131:3 (2007) : 391-394
47. Yagmur, L., Fank, S., Aydemir, B. "Effect of Microstructure on Modulus Loss at Flexural Mode and Stress in Sensor Materials", Sensors and Actuators, A: Physical, 136:1 (2007) : 261-266
48. Aydemir, B., Fank, S., Cal, B. "Effect of Test Speed on Verification of Material Testing Machine", Measurement, 40:3 (2007) : 343–346
49. Fank, S., Kumme, R., Aydemir, B., Pelit, E., Glockner, B., Haucke, G. "Intercomparison of 3 mn Hydraulic Type Build-up and 1.1 mn Lever Amplification Force Standard Machine between UME and PTB", 18th IMEKO World Congress 2006: Metrology for a Sustainable Development, Rio de Janeiro, 17-22 September 2006, 3:- (2006) : 1852-1854
50. Sayinsu, K., Isik, F., Sezen, S., Aydemir, B. "Light Curing the Primer - Beneficial When Working in Problem Areas?", Angle Orthodontist, 76:2 (2006) : 310-313
51. Sayinsu, K., Isik, F., Sezen, S., Aydemir, B. "New Protective Polish Effects on Shear Bond Strength of Brackets", Angle Orthodontist, 76:2 (2006) : 306-309
52. Aydemir, B., Kaluc, E., Fank, S. "Influence of Heat Treatment on Hysteresis Error of Force Transducers Manufactured from 17-4PH Stainless Steel", Measurement, 39:10 (2006) : 892–900
53. Fank, S., Demirkol, M. "Effect of Microstructure on the Hysteresis Performance of Force Transducers Using AISI 4340 Steel Spring Material", Sensors and Actuators A: Physical, 126:1 (2006) : 25–32
54. Dogan, C., Akkoyunlu, O., Kuzu, C. "Development of the 1 kNm Sstatic Torque Standard Machine at UME", 18th IMEKO TC3 Conference on Force, Mass and Torque, Germany, 24-26 September 2002, -:- (2002) : 294-297
55. Fank, S., Gloeckner, B., Kuzu, C., Pelit, E., Aydemir, B., Cal, B. "Intercomparison Results of UME Force Standard Machines with PTB after 1999 Marmara Eearthquake", 17th IMEKO TC3 Conference on Force, Mass and Torque 2001, Istanbul, 17 -21 September 2001, -:- (2001) : 371-372
56. Orhan, M., Dogan, C., Kocabas, H., Tepehan, G. "Experimental Strain Analysis of the High Pressure Strain Gauge Pressure Transducer and Verification by Using Finite Element Method", Measurement Science and Technology, 12:3 (2001) : 335–344


  BİLDİRİ
1. Kuru, U., Dizdar, H., Yucebag, C. "Roket Motorunun İtme Kuvveti Ölçümü için Test Platformunun Tasarımı ve Teorik Analizi", International Marmara Sciences Congress (Imascon 2024 – Spring) , Kocaeli (31/05-01/06/2024) : 6 p.
2. Danaci, E., Aydemir, B. "TUBITAK UME Digital Metrology Pilot Project and Dissemination at Turkiye", 4th Digital Calibration Certificate Conference, Online (27-29/02/2024) : 11 p.
3. Kuru, U., Aydemir, B. "Kullanılan Aparatın Kuvvet Ölçme Cihazı Kalibrasyonlarına Etkisinin İncelenmesi", International Marmara Sciences Congress (Imascon 2023 – Autumn), Kocaeli (15-16/12/2023) : 5 p.
4. Aydemir, B. "Bir Yaklaşım - Kuvvet Ölçümlerinde Mesafe Doğruluğu Etkileri Üzerine", International Marmara Sciences Congress (Imascon 2023 – Autumn), Kocaeli (15-16/12/2023) : 5 p.
5. Uzun, S., Arifovic, M., Aydemir, B., Kuru, U. "Vucut Direnci Ölçüm Sistemi İle Farklı Etkinliklerde Elde Edilen Sonuçlarının İncelenmesi", International Marmara Sciences Congress (Imascon 2023 – Autumn), Kocaeli (15-16/12/2023) : 6 p.
6. Ebcim, E., Aydemir, B. "Kalibrasyon Laboratuvarında İş Akış Sürecinde Zaman Etüdünün Değerlendirilmesi", International Marmara Sciences Congress (Imascon 2023 – Autumn), Kocaeli (15-16/12/2023) : 6 p.
7. Danaci, E., Aydemir, B. "Dijital Kalibrasyon Sertifika Süreci", International Marmara Sciences Congress (Imascon Autum 2023), Kocaeli (15-16/12/2023) : 5 p.
8. Demir, T., Aydemir, B. "Topsis Karar Verme Tekniği İle Kamyon Kantarı Ölçüm Düzeneği İçin Uygun Yük Hücresi Seçimi", International Marmara Sciences Congress (Imascon Spring 2023), Kocaeli (09-10/06/2023) : 7 p.
9. Badem, F., Aydemir, B. "Vagon Kantarı Sistemi Tasarımı Ve Analizi", International Marmara Sciences Congress (Imascon Spring 2023) , Kocaeli (09-10/06/2023) : 6 p.
10. Aydemir, B., Kuru, U. "Traceability Need of Earthquake Isolator Performance Test Machine", 6th International Iron&Steel Symposium (UDCS 23), Karabük (11-13/05/2023) : 4 p.
11. Badem, F., Aydemir, B. "Vagon Kantarı Ölçüm Sistemi İçin Uygun Yük Hücresinin Karar Verme Tekniği İle Seçimi", International Marmara Sciences Congress (Imascon Spring 2023) , Kocaeli (09-10/06/2023) : 8 p.
12. Demir, T., Aydemir, B. "Solidworks İle Kamyom Kantarı Tasarımı Ve Analizi", International Marmara Sciences Congress (Imascon Spring 2023), Kocaeli (09-10/06/2023) : 5 p.
13. Aydemir, B. "Effects of Sample Geometry and Gauge Length on Tensile Test Results", 6th International Iron&Steel Symposium (UDCS 23), Karabük (11-13/05/2023) : 4 p.
14. Kuru, U., Aydemir, B. "Deprem İzolatör Test Cihazının Ekstansometre Ölçüm Sisteminin Kalibrasyon Gerekliliği", International Marmara Sciences Congress (Imascon Spring 2023), Kocaeli (09-10/06/2023) : 7 p.
15. Danaci, E., Aydemir, B. "Geleceğin Laboratuvarlari ve Laboratuvarlarin Geleceği Üzerine Öngörüler", International Marmara Sciences Congress (Imascon Spring 2023) , Kocaeli (09-10/06/2023) : 9 p.
16. Aydemir, B., Kuru, U. "Rezanatör Tip Kuvvet Ölçüm Cihazları ve Diğer Sensörlere Göre Farklılıkları", International Marmara Sciences Congress (IMASCON 2022 Spring), Kocaeli (13-14/05/2022) : 7 p.
17. Ayik, K.D., Aydemir, B., Kuru, U. "Galvano Manyetik Kuvvet Ölçme Cihazları ve Uygulama Alanları", International Marmara Sciences Congress (IMASCON 2022 Spring), Kocaeli (13-14/05/2022) : 8 p.
18. Kuzu, C., Pelit, E., Meral, I. "Design and Development of Hardness Indentation Measurement System at TÜBİTAK UME", IMEKO TC3, TC5, TC16 and TC22 International Conference , Dubrovnik (11-13/10/2022) : 4 p.
19. Kuzu, C., Pelit, E. "A New Approach to Force Traceability in Hardness Measurements", IMEKO TC3, TC5, TC16 and TC22 International Conference, Dubrovnik (11-13/10/2022) : 5 p.
20. Kuzu, C., Pelit, E. "Installation and Metrological Characterization of High Load Brinell Hardness Standard Machine at TÜBİTAK UME", IMEKO TC3, TC5, TC16 and TC22 International Conference, Dubrovnik (11-13/10/2022) : 4 p.
21. Aydemir, B. "Kuvvet Ölçme Cihazlarında Hatalı Kuvvet Ölçümüne Neden Olan Şartlar", 9th International Marmara Sciences Congress (Imascon Autumn) , Kocaeli (09-10/12/2022) : 6 p.
22. Kuru, U., Aydemir, B., Uzun, S. "Farklı Etkinliklerdeki El Sıkma Kuvveti Ölçme Sistemi İle Alınan Verilerin İncelenmesi", 9th International Marmara Sciences Congress (Imascon Autumn) , Kocaeli (09-10/12/2022) : 6 p.
23. Danaci, E., Aydemir, B. "SI Birimlerindeki Değişikliklerin Etkilerinin İncelenmesi ", 9th International Marmara Sciences Congress (IMASCON Autumn), Kocaeli (09-10/12/2022) : 10 p.
24. Aydemir, B. "Diş Malzemelerinde Mekanik Testler ve Doğru Test İçin Gereklilikler", 7th International Mediterranean Science and Engineering Congress (IMSEC), Alanya (24-26/10/2022) : 8 p.
25. Aydemir, B. "Malzeme Basma Testlerin Detayları ve Sonuçlarının Yorumlanması = Material Compression Tests, Details, and Interpretation of Results", 7th International Mediterranean Science and Engineering Congress (IMSEC), Alanya (24-26/10/2022) : 7 p.
26. Aydemir, B., Dizdar, H., Vatan, C. "The Method Proposal for Calibration of the Alignment Cell", IMEKO 24th TC3, 14th TC5, 6th TC16 and 5th TC22 International Conference , Dubrovnik (11-13/10/2022) : 5 p.
27. Aydemir, B., Dizdar, H., Vatan, C. "Investigation of the Effect of Waiting Time in Force Steps During Force Calibration", 24th IMEKO TC3, 14th IMEKO TC5, 6th IMEKO TC16 and 5th IMEKO TC22 International Conference, Dubrovnik (11-13/10/2022) : 5 p.
28. Dizdar, H., Aydemir, B., Vatan, C. "Evaluation of the Effect of Dynamic Verification on Different Types of Force Sensors", IMEKO 24th TC3, 14th TC5, 6th TC16 and 5th TC22 International Conference , Dubrovnik (11-13/10/2022) : 6 p.
29. Aydemir, B., Aydin, H., Guler, F., Gungor, A., Kucukogul, I., Zeytin, H.K. "Evaluation of Proficiency Test Results in HighTemperature Tensile Test in Aerospace Metallic", 21st International Metallurgy and Materials Congress (IMMC 2022), İstanbul (06-08/10/2022) : 3 p.
30. Aydemir, B., Aydin, H., Guler, F., Gungor, A., Kucukogul, I., Zeytin, H.K. "Evaluation of Proficiency Test Results in Fatigue Test in Aerospace Metallic Materials", 21st International Metallurgy and Materials Congress (IMMC 2022), İstanbul (06-08/10/2022) : 3 p.
31. Kuzu, C., Pelit, E., Meral, I. "Installation and Metrological Characterization of Rockwell-Brinell-Vickers Hardness Standard Machine at TÜBİTAK UME", IMEKO 24 TC3, TC5, TC16 and TC22 International Conference, Dubrovnik (11-13/10/2022) : 4 p.
32. Dogan, C., Tunaci, S., A. Bin Jarbua, S., M. Alqarni, S. "50 N·m Torque Standard Machine at SASO/NMCC", IMEKO 24 th TC3, 14 th TC5, 6 th TC16 and 5 th TC22 International Conference, Dubrovnik (11-13/10/2022) : 4 p.
33. Dogan, C., Tunaci, S., A. Bin Jarbua, S., M. Alqarni, S. "1 kN·m Universal Torque Calibration Machine with Reference Torque Transducer at SASO/NMCC", IMEKO 24 th TC3, 14 th TC5, 6 th TC16 and 5 th TC22 International Conference, Dubrovnik (10-13/10/2022) : 4 p.
34. Uzun, S., Arifovic, M., Aydemir, B. "Geliştirilen Vucut Direnci Ölçüm Sistemi ve Ölçüm Sonuçlarının Değerlendirilmesi", International Marmara Sciences Congress (Imascon Spring) 2022, Kocaeli (13-14/05/2022) : 7 p.
35. Kuru, U., Aydemir, B. "El Sıkma Kuvveti Ölçümü İçin Geliştirilen Sistem ve Ölçüm Sonuçlarının Değerlendirilmesi", International Marmara Sciences Congress (Imascon Spring 2022), Kocaeli (13-14/05/2022) : 7 p.
36. Akbas, F., Aydemir, B. "Titreşimli Tel Kuvvet Dönüştürücülerinin İncelenmesi", International Marmara Sciences Congress (Autumn) 2021 (IMASCON 2021), Kocaeli (10-11/12/2021) : 1 p.
37. Akbas, F., Aydemir, B. "Akustik Kuvvet Dönüştürücülerin Yapısının, Tiplerinin ve Uygulamalarının İncelenmesi", International Marmara Sciences Congress (Autumn) 2021 (IMASCON 2021), Kocaeli (10-11/12/2021) : 8 p.
38. Aydemir, B. "The Use And Importance of Strain Gauges For Experimental Stress Analysis in Composite Material Tests", 6nd International Conference on Material Science and Technology in Cappadocia (IMSTEC’21), Cappadocia /TURKEY (26-28/11/2021) : 6 p.
39. Germak, A., Kuzu, C., Origlia, C., Pelit, E., Menelao, F. "Result Analysis of EURAMET Brinell Comparison Between INRiM, UME and PTB (EURAMET.M.H–S2.A.B)", XXIII IMEKO World Congress, Yokohama (30/08-03/09/2021) : 5 p.
40. Sepetcioglu, H., Aydemir, B. "Plastik Malzemelerin Çekme Testinde Hızın Sonuçlar Üzerinde Etkisinin Araştırılması", 6th International Mediterranean Science and Engineering Congress (IMSEC 2021), Antalya (25-27/10/2021) : 6 p.
41. Guler, F., Akbas, F., Aydemir, B. "Direnç Değişimi ile Çalışan Kuvvet Ölçme Cihazlarının Esasları, Tipleri ve Uygulamaları", 6th International Mediterranean Science and Engineering Congress (IMSEC 2021), Antalya (25-27/10/2021) : 6 p.
42. Akbas, F., Guler, F., Aydemir, B. "Kapasitif Etki Prensipli Kuvvet Ölçme Cihazlarının Yapısı, Türleri ve Kullanım Alanlarının İncelenmesi", 6th International Mediterranean Science and Engineering Congress (IMSEC 2021), Antalya (25-27/10/2021) : 7 p.
43. Kuzu, C., Germak, A., Origlia, C., Pelit, E. "Result Analysis of EURAMET Vickers Comparison Between INRiM and UME (EURAMET.M.H-K1.b.c)", XXIII IMEKO World Congress, Yokohama (30/08-03/09/2021) : 5 p.
44. Dizdar, H., Aydemir, B., Vatan, C. "Establishment of Continuous Force Calibration System at TUBITAK UME Force Laboratory in Turkey", XXIII IMEKO World Congress, Yokohama (30/08-03/09/2021) : 4 p.
45. Aydemir, B., Tascan, H., Camyurdu, C., Kurttepeli, S. "Civata Çekme Deneyinde Karşılaşılabilecek Sorunlar ve Etkileri", International Marmara Sciences Congress (Spring) (IMASCON 2021), Kocaeli (21-22/05/2021) : 8 p.
46. Altinok, M., Aydemir, B. "Roket Motoru Test Düzeneği için Uygun Yük Hücresinin Karar Verme Tekniği ile Seçimi", 4. International Conference on Materials Science, Mechanical and Automotive Engineerings and Technology (IMSMATEC'21), Nevşehir (28-30/05/2021) : 8 p.
47. Altinok, M., Aydemir, B. "Roket Test Motoru Test Düzeneğinin Tasarımı ve Analizi", 4. International Conference on Materials Science, Mechanical and Automotive Engineerings and Technology (IMSMATEC'21), Nevşehir (28-30/05/2021) : 6 p.
48. Aydemir, B., Kacar, B. "ISO 6892-2 Standardına göre Metalik Malzemelerin Yüksek Sıcaklıkta Çekme Deneyi Yönteminin İncelenmesi", 4. International Conference on Materials Science, Mechanical and Automotive Engineerings and Technology (IMSMATEC'21), Nevşehir (28-30/05/2021) : 5 p.
49. Kacar, B., Aydemir, B., Dizdar, H., Vatan, C., Kuru, U. "An Approach to Uncertainty Calculation of the Modulus of Elasticity for Metallic Materials", Fifth International Iron & Steel Symposium (UDCS 21), Karabük (01-03/04/2021) : 4 p.
50. Aydemir, B. "Green Steel and Future Steel Visions", Fifth International Iron & Steel Symposium (UDCS 21), Karabük (01-03/04/2021) : 4 p.
51. Altinok, M., Aydemir, B., Gulen, A.U. "Elektro Manyetik Kuvvet Ölçme Cihazı Yapısının ve Kullanım Yerlerinin İncelenmesi=Investigation of the Structure and Usage of Electro Magnetic Force Measuring Instruments", 5th International Mediterranean Science and Engineering Congress (IMSEC 2020), Antalya (21-23/10/2020) : 6 p.
52. Altinok, M., Aydemir, B., Gulen, A.U. "Manyeto Elastik Kuvvet Ölçme Cihaz Yapılarının İncelenmesi=Investigation of the Structure of Magneto Elastic Force Measuring Instruments", 5th International Mediterranean Science and Engineering Congress (IMSEC 2020), Antalya (21-23/10/2020) : 8 p.
53. Aydemir, B., Tascan, H. "Effects of Sample Shapes on Tensile Test Results in Stretch Film Materials = Streç Film Malzemelerde Numune Şekillerinin Çekme Deneyi Sonuçlarına Etkileri", 3. International Conference on Materials Science, Mechanical and Automotive Engineerings and Technology (IMSMATEC'20),İstanbul (24-26/06/2020) : 4 p.
54. Soykan, S., Aydemir, B. "Stentler, Özelikleri ve Mekanik Testleri", International Marmara Sciences Congress Autumn (IMASCON) 2019,Kocaeli (01-03/11/2019) : 6 p.
55. Dizdar, H., Aydemir, B. "Piezo Elektrik Kuvvet Sensörlerinin Kalibrasyonu ve Belirsizlik Analizi", International Marmara Sciences Congress Autumn (IMASCON 2019),Kocaeli (01-03/11/2019) : 7 p.
56. Durgut, Y., Yilmaz, R., Aydemir, B., Bagci, E. "Dinamik Basınç Sensörlerinin Kalibrasyonu İçin Referans Standard Geliştirilmesi", 7th International Symposium on Innovative Technologies in Engineering and Science,Şanlıurfa (22-24/11/2019) : 8 p.
57. Aydemir, B. "Çekme Deneyinde Gerilme Oranı veya Uzama Oranı Olarak Tanımlanan Hızların Sağlanabilmesi İçin Hareketli Tabla Hızınını Belirlenmesi=Determining Crosshead Speed to Provide Test Speeds Defined as Stress-Rate or Strain-Rate in Tensile Test", 4nd International Conference on Material Science and Technology (IMSTEC?19),Ankara (18-20/10/2019) : 4 p.
58. Aydemir, B., Soykan, S. "Stentlere Uygulanan Mekanik Testlerin İncelenmesi=Investigation of Mechanical Tests Applied to Stents", 4nd International Conference on Material Science and Technology (IMSTEC?19),Ankara (18-20/10/2019) : 7 p.
59. Aydemir, B., Elmas, B.S., Ayan, E. "Jiroskopik Kuvvet Ölçme Cihazlarının İncelenmesi", Uluslararası Marmara Fen ve Sosyal Bilimler Kongresi (Bahar) 2019 (IMASCON 2019),Kocaeli (26-28/04/2019) : 10 p.
60. Dizdar, H., Aydemir, B., Vatan, C. "Impact Test Applications in Steel Industry, Testing and Uncertainty Calculation", Fourth International Iron and Steel Symposium (UDCS'19),Karabük (04-06/04/2019) : 5 p.
61. Aydemir, B., Ayan, E., Elmas, B.S., Dizdar, H. "Piezoelektrik Kuvvet Ölçme Cihazlarının Yapısı, Avantajları ve Kalibrasyonu = Structure, Advantages and Calibration of Piezoelectric Force Measurement Devices", 4th International Mediterranean Science and Engineering Congress (IMSEC 2019),Antalya (25-27/04/2019) : 7 p.
62. Aydemir, B., Elmas, B.S., Ayan, E. "Çekme Deneyinde Elastisite Modülü Hesap Yöntemleri ve Hata Kaynakları = Elastic Modulus Measurement Methods and Error Sources in Tensile Testing", 4th International Mediterranean Science and Engineering Congress (IMSEC 2019),Antalya (25-27/04/2019) : 7 p.
63. Vatan, C., Aydemir, B., Kuru, U., Dizdar, H. "Evaluation of Proficiency Test Result of Tensile Testing for Metallic Material", Fourth International Iron and Steel Symposium (UDCS'19),Karabük (04-06/04/2019) : 4 p.
64. Ercan, B., Akgul, Y., Incesu, A., Abunaz, M., Aydemir, B., Kavruk, M. "A Case Study: Investigation of the Contribution of Accredited Laboratories on the Iron & Steel Sector in Turkey", Fourth International Iron and Steel Symposium (UDCS'19),Karabük (04-06/04/2019) : 5 p.
65. Aydemir, B. "The Place in Europe of Test Laboratories in Turkey - According to ISO 6892-1 Standard", Fourth International Iron and Steel Symposium (UDCS'19),Karabük (04-06/04/2019) : 5 p.
66. Incesu, A., Akgul, Y., Ercan, B., Abunaz, M., Aydemir, B., Kavruk, M. "The Relationship Between Steel Production and Accredited Laboratory", Fourth International Iron and Steel Symposium (UDCS'19),Karabük (04-06/04/2019) : 5 p.
67. Tigrel, F., Fank, S., Kaya, H. "A New 500 Kg Dead-Weight Machine for Test Load Cell According to OIML R60 and Performance Tests Realised by UME", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : 8 p.
68. Orhan, M., Dogan, C., Kocabas, H., Tepehan, G. "3-D Finite Element Modelling of a High Pressure Strain Gauge Pressure Transducer", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : 5 p.
69. Durgut, Y., Aydemir, B., Bagci, E., Aksahin, E., Ince, A.T. "Development of Dynamic Calibration Machine for Pressure", XXII World Congress of the International Measurement Confederation (IMEKO 2018),Belfast (03-06/09/2018) : 4 p.
70. Aydemir, B. "Çentik Darbe Testlerinde Ölçüm Belirsizliği Uygulaması = Application of Measurement Uncertainty in Notch Impact Tests", 3nd International Conference on Material Science and Technology in Cappadocia (IMSTEC?18),Nevşehir (17-19/09/2018) : 5 p.
71. Aydemir, B., Yagmur, L. "Yük Hücresi Gövde Malzemesinin Seçiminde Analitik Yöntem Yaklaşımının (AHP) Kullanımı = Using of The Analytic Hierarchy Process (AHP) in The Selection of Materials in The Loadcell Body", 3nd International Conference on Material Science and Technology in Cappadocia (IMSTEC?18),Nevşehir (17-19/09/2018) : 6 p.
72. Aydemir, B., Dizdar, H., Vatan, C., Inan, G., Tascan, H., Camyurdu, C. "Plastik Malzeme Çekme Deneyinde Yeterlilik Testi Sonuçlarının Değerlendirilmesi = Evalation of Proficiency Test Results in Tensile Test", 3nd International Conference on Material Science and Technology in Cappadocia (IMSTEC?18),Nevşehir (17-19/09/2018) : 4 p.
73. Kuzu, C., Meral, I., Pelit, E. "Metrological Characterization of Hardness Indenter Calibration System", XXII IMEKO World Congress,Belfast (03-06/09/2018) : 4 p.
74. Aydemir, B., Vatan, C., Dizdar, H., Binown, A., Algamdi, H., Algamdi, M. "Comparison on Force Standard Machines between TÜBİTAK UME and SASO NMCC", XXII IMEKO World Congress,Belfast (03-06/09/2018) : 4 p.
75. Kavruk, M., Abunaz, M., Aydemir, B. "Akredite Laboratuvarın Demir Çelik Sanayisine Etkisi - Sektör Analizi", The Internatinonal Conference on Materials Science Mechanical and Automation Engineerings and Technology (IMSMATEC?18),İzmir (10-12/04/2018) : 8 p.
76. Aydemir, B., Dizdar, H., Vatan, C. "Importance of Test Speed on Tensile Testing Machines and its Verification", The International Conference on Materials Science Mechanical and Automation Engineering and Technology (IMSMATEC?18),İzmir (10-12/04/2018) : 5 p.
77. Telli, G.M., Aydemir, B. "Fotovolta,k Panellerde Tangın Testleri ve Önemi", 2nd International Mediterranean Science and Engineering Congress (IMSEC 2017),Adana (25-27/10/2017) : 7 p.
78. Aydemir, B., Tascan, H., Camyurdu, C., Baran, O., Temiz, A. "Investigation of Effects on the Results of Different Test Rates in Metallic", 2nd International Conference on Material Science and Technology in Cappadocia (IMSTEC?17),Nevşehir (11-13/10/2017) : 6 p.
79. Aydemir, B., Sahin, S., Sahin, T. "Effect of Particle Size of Calcium Carbonate on the Short-Term Tensile Creep Properties of Polypropylene Block Copolymer", 2nd International Conference on Material Science and Technology in Cappadocia (IMSTEC?17),Nevşehir (11-13/10/2017) : 4 p.
80. Dizdar, H., Aydemir, B., Vatan, C. "Differences of Latest Versions of ISO 6892-1 and ASTM E8 Tensile Testing Standards", 2nd International Conference on Material Science and Technology in Cappadocia (IMSTEC?17),Nevşehir (11-13/10/2017) : 6 p.
81. Dizdar, H., Aydemir, B., Vatan, C. "Importance of Force Measurements and Their Traceability in Steel Industry", 3rd International Iron & Steel Symposium (UDCS 17),Karabük (03-05/04/2017) : 4 p.
82. Kavruk, M., Aydemir, B. "Analysis of Accredited Laboratories in the Steel Sector in Turkey", 3rd Iron and Steel Symposium (UDCS?17),Karabük (03-05/04/2017) : 6 p.
83. Aydemir, B. "The Changes in ISO 6892-1:2016 Metallic Materials Tensile Testing Standard", 3rd Iron and Steel Symposium (UDCS?17) ,Karabük (03-05/04/2017) : 4 p.
84. Dizdar, H., Aydemir, B., Vatan, C. "Importance of Force Measurements and Their Traceability in Steel Industry", 3rd Iron and Steel Symposium (UDCS?17) ,Karabük (03-05/04/2017) : 4 p.
85. Aydemir, B., Ozgen, D., Durgut, Y., Kucuk, O., Ozal, A.S., Tosun, I. "Dinamik Ölçümlerde Sensör Uygulamaları", 1st International Mediterranean Science and Engineering Congress (IMSEC 2016),Adana (26-28/10/2016) : 8 p.
86. Dizdar, H., Vatan, C., Aydemir, B. "Kuvvet Ölçümlerinde Bağıl Enterpolasyon Hatasının Farklı Matematiksel Yöntemlerle Hesaplanması ve Sayısal Örneklenmesi", 1st International Mediterranean Science and Engineering Congress (IMSEC 2016),Adana (26-28/10/2016) : 9 p.
87. Aydemir, B., Vatan, C., Dizdar, H. "Malzeme Test Makinalarında Eksenellik Ölçümü ve Önemi", 1st International Mediterranean Science and Engineering Congress (IMSEC 2016),Adana (26-28/10/2016) : 7 p.
88. Aydemir, B., Fank, S. "Calculation of Measurement Uncertainty for Elasticity Module of Automobile Deadening Panels", 2nd International Conference on Computational and Experimental Science and Engineering (ICCESEN 2015),Antalya (14-19/10/2015) : 1 p.
89. Fank, S., Aydemir, B. "Need of Traceable Force Measurements in Steel Industry Meganewton Level Forces", 2nd International Conference on Computational and Experimental Science and Engineering (ICCESEN 2015),Antalya (14-19/10/2015) : 1 p.
90. Kuzu, C., Pelit, E., Dogan, C., Okur, A., Meral, I., Ozgur, B., Kazmanli, K. "Design and Development of Brinell-Vickers Hardness Standard Machine", XXI IMEKO World Congress ,Prag (30/08-04/09/2015) : 5 p.
91. Kuzu, C., Pelit, E., Dogan, C., Okur, A., Meral, I., Yandayan, T., Kazmanli, K. "A New Design and Automation of Rockwell Hardness Standard Machine", XXI IMEKO World Congress ,Prag (30/08-04/09/2015) : 6 p.
92. Kuzu, C., Pelit, E., Ganioglu, O. "Interlaboratory Comparison on Calibration of Durometers of Types A and D in Turkey", XXI World Congress IMEKO 2015,Prag (30/08-04/09/2015) : 7 p.
93. Durgut, Y., Aksahin, E., Bagci, E., Fank, S., Ince, A., Aydemir, B. "Preliminary Dynamic Pressure Measurement System at UME", XXI IMEKO World Congress,Prag (30/08-04/09/2015) : 4 p.
94. Aydemir, B., Fank, S., Vatan, C., Anil, D., Kuyrukluyildiz, A. "Design Development and Establishment og 1 KN Force Calibration Machine in Force Laboratory of TSE", XXI IMEKO World Congress,Prag (30/08-04/09/2015) : 4 p.
95. Aydemir, B., Kazdal, H., Guven, G., Gungor, A. "Investigation of Mechanical Properties of DP 600 Steels at Elevated Temperatures", 2nd International Symposium on Innovative Technologies in Engineering and Science (ISITES 2014),Karabük (18-20/06/2014) : 6 p.
96. Aydemir, B., Zeytin, H., Guven, G., Gungor, A. "Deformation Behaviour of Cold-Formed 32Mn2.3Si3Al TWIP Steel in Tension at Different Temperatures", 2nd International Symposium on Innovative Technologies in Engineering and Science (ISITES 2014),Karabük (18-20/06/2014) : 6 p.
97. Durgut, Y., Fank, S., Aydemir, B. "Darbe Test Makinasının Dinamik Basınç Transduserlerinin Kalibrasyonlarına Uygulanması", 7th International Advanced Technologies Symposium (IATS?13),İstanbul (30/09-01/11/2013) : 6 p.
98. Kacmaz, S., Akcadag, U., Aydemir, B. "Micro-Mass Standards And Short Time Instabilities", XX IMEKO World Congress Metrology for Green Growth,Busan (09-14/09/2012) : 793 p.
99. Kuzu, C., Oysu, C., Fank, S., Pelit, E. "Establishment of Rockwell Hardness Scales at UME", XX IMEKO World Congress Metrology for Green Growth,Busan (09-14/09/2012) : 5 p.
100. Kuzu, C., Pelit, E. "Interlaboratory Comparison in Calibration of Hardness Testing Machines in Turkey", XX IMEKO World Congress Metrology for Green Growth,Busan (09-14/09/2012) : 5 p.
101. Gunay, A., Fank, S., Gulmez, T., Durakbasa, N. "Calculation Of Measurement Uncertainty For Plastıc (ABS) Material In Flexural Testing", XX IMEKO World Congress Metrology for Green Growth,Busan (09-14/09/2012) : 4 p.
102. Aydemir, B., Fank, S., Vatan, C. "Interlaboratory Comparısons Performed in Turkey: Force Calibration Of Static Material Testing Machines", XX IMEKO World Congress Metrology for Green Growth,Busan (09-14/09/2012) : 4 p.
103. Unver, I., Gulsoy, H., Aydemir, B. "Sintering-Dissolution Process For Manufacturing Ni-625 Superalloy Foams", 67th ABM International Congress,Rio De Janeiro (31/07-03/08/2012) : 7 p.
104. Fank, S., Aydemir, B. "Calculation of Measurement Uncertainty for Cellulose Based Transformed Board Material in Tensile Testing", 4th International Metrology Conference CAFMET 2012,Marrakech (23-27/04/2012) : 5 p.
105. Aydemir, B., Fank, S. "Interlaboratory Proficiency Testing of Tensile and Flexural Testing for Cellulose Based Transformed Board Material", 4th International Metrology Conference CAFMET 2012,Marrakech (23-27/04/2012) : p.
106. Aydemir, B., Akgul, Y., Tolay, E. "Demiryolu Uygulamalarında Vagonların Yük ve Güvenlik Kontrolünün İzlenmesi", International Iron & Steel Symposium,Karabük (02-04/04/2012) : 8 p.
107. Yilmaz, A., Kuntman, A., Aydemir, B. "The Effect of Nanometer Size Mica Fillers on Mechanical Properties of Polyurethane", 6th Nanoscience and Nanotechnology Conference,İzmir (15/06-17/10/2010) : 1 p.
108. Aliyev, E., Akkoyunlu, O., Yeken, T. "Three-Dimensional Stability Problems of the Viscoelastic Materials", Mechanics Of Composite Materials Conference,Riga (24-28/05/2012) : 32 p.
109. Kuzu, C. "Establisment of Brinell and Vickers Hardness Scales at UME", XIX IMEKO World Congresses Fundamental and Applied Metrology,Lisbon (06-11/09/2009) : 6 p.
110. Fank, S., Kumme, R., Aydemir, B., Pelit, E., Glockner, B., Haucke, G. "Intercomparison of 3 mn Hydraulic Type Build-up and 1.1 mn Lever Amplification Force Standard Machine Between UME and PTB", XVIII IMEKO World Congress, Metrology for a Sustainable Development,Rio de Janeiro (17-22/09/2006) : 3 p.
111. Fank, S., Ozbay, H.O., Pelit, E., Kuzu, C., Aydemir, B., Cal, B. "3 MN Hydraulic Type Build-Up Force Standard Machine Installed at National Metrology Institute (UME),", XVII IMEKO World Congress - Metrology in the 3rd Millennium,Dubrovnik (22-27/06/2003) : 4 p.
112. Dogan, C., Akkoyunlu, O., Kuzu, C. "Development of the 1 kNm Static Torque Standard Machine at UME", 18th Conference on Force, Mass and Torque (IMEKO TC3 Conference),Celle (24-26/09/2002) : 5 p.
113. Tigrel, F., Fank, S., Kaya, H. "A New 500 kg Dead Weight Machine for Load Cell Test Accorging to OIML R60 and Performance Test Realised by UME", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : p.
114. Fank, S., Kuzu, C., Pelit, E., Aydemir, B., Cal, B. "Intercomparison Results of UME Force Standard Machines with PTB After 1999 Marmara Earthquake", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : p.
115. Bilgic, E., Karaboce, B., Sadikoglu, E., Fank, S. "Influence of Mechanical Vibration on Strain Gage based Force Transducer Performance", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : p.
116. Fank, S., Demirkol, M. "Effect of Hardness on Creep Response of Strain Gage based Force Transducer Using AISI 4340 Steel as Spring Material", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : p.
117. Bilgic, E., Karaboce, B., Fank, S., Sadikoglu, E. "Influence of Mechanical Vibration on Strain Gauge Based Force Transducer Performance", 17th Conference on Force, Mass and Torque (IMEKO TC3 Conference),İstanbul (17-21/09/2001) : p.
118. Fank, S., Orhan, M., Kacmaz, S. "Effect of Interpolation Equations on the Evaluation of Measurement Uncertainty", XV. IMEKO World Congress,Osaka (13/06-18/09/1999) : 6 p.
119. Fank, S., Orhan, H., Kacmaz, S. "Effect of Interpolation Equations on the Evaluation of Measurement", XV. IMEKO World Congress,Osaka (13-19/06/1999) : 6 p.
120. Fank, S., Parlakturk, H. "The Possibility of Force Transducer Calibration Using With Lower Capacity Force Standard Machines", 16th Conference on Measurement of Force and Mass (IMEKO TC3),Teajon (14-18/09/1998) : 5 p.
121. Fank, S. "A New 0.5 - 500 N Range Force Standard Systems for the Force Calibration Laboratories", 16th Conference on Measurement of Force and Mass (IMEKO TC3),Taejon (14-18/09/1998) : 10 p.
122. Fank, S., Sawla, A., Ozbay, H. "Long Term Observation of Newly Developed 110 kN/1.1 MN Lever Amplification Dead Weight Force Standard Machine at UME", XIV. IMEKO World Congress,Tampere (01-06/06/1997) : 7 p.
123. Fank, S., Sawla, A., Ozbay, H., Gassmann, H. "Establishment of National Force Scale at UME and Results of Intercomparison Measurements Between UME and PTB", 15th Conference on Measurement of Force and Mass (IMEKO TC-3), Madrid (07-11/10/1996) : 11 p.


  KARŞILAŞTIRMA RAPORU
1. Germak, A., Kuzu, C., Origlia, C., Pelit, E. "Key Comparison Between INRiM and UME in Vickers Hardness Scales (HV1-HV30)" (2021) : 19 p.
2. Germak, A., Kuzu, C., Origlia, C., Pelit, E., Menelao, F. "Euramet Supplementary Comparıson Between INRiM, UME and PTB in Brınell Hardness Scales (HBW1/30 – HBW2.5/187.5)" (2021) : 16 p.
3. Germak, A., Kuzu, C., Origlia, C., Pelit, E. "Euramet Supplementary Comparison Between Inrim And UME in Rockwell Hardness Scales (HRA - HRBW - HRC)" (2020) : 17 p.
4. Kuzu, C., Pelit, E. "UME-SASO Hardness Comparison UME ST D3 2.9.6.a Draft-A" (2017) : 8 p.
5. Kuzu, C., Pelit, E. "Bilateral Comparison on Calibration of Hardness Reference Blocks Between TÜBİTAK UME and SASO NMCC Draft A Report (UME-ST-D3-2.9.6.a)" (2018) : 8 p.
6. Kuzu, C., Pelit, E. "Bilateral Comparison on Calibration of Hardness Reference Blocks Between TÜBİTAK UME and SASO NMCC Draft B Report (UME-ST-D3-2.9.6.a)" (2018) : 8 p.
7. Aydemir, B., Vatan, C., Dizdar, H., Binown, A. "Final Report Bilateral Comparison on Force Standard Machines Between TUBITAK UME and SASO NMCC -GULFMET.M.F-S2" (2017) : 25 p.
8. Aydemir, B., Vatan, C., Dizdar, H., Binown, A. "Dfart a Report Bilateral Comparison on Force Standard Machines Between TUBITAK UME and SASO NMCC -GULFMET.M.F-S2" (2017) : 23 p.
9. Aydemir, B., Vatan, C., Dizdar, H. "GULFMET-M-F-S1 Technical Protokol Comparison of Force Standard Machines" (2018) : 15 p.
10. Aydemir, B., Vatan, C., Dizdar, H., Jarbua, S., Binown, A., Alaydan, M. "Report of Bilateral Comparison on Force Standard Machines Between TUBITAK UME and SASO NMCC (UME-KV-D3-2.10.6.a)" (2016) : 36 p.
11. Fank, S., Aydemir, B., Vatan, C., Gherasimov, A., Pomarlan, M., Hodor, D. "Draft B Report on Bilateral (Suplementary) Comparison in the Range 200 kN to 1000 kN of TUBITAK UME and INM Force Standard Machines (EURAMET 838 Project)" (2016) : 48 p.


  REHBER DOKÜMAN
1. Kumme, R., Tegtmeier , F., Sander, J., Hauschild, F., Gerber, S., Nitschke, A., Neumann, S., Oliveira, R.S., Machado, R.R., Wozniak, M., Dizdar, H., Aydemir, B., Korhonen, J., Hiti, M., Luká? , V. "Guidelines Detailing Recommendations and Standards for Force Calibration of Testing Machines Under Dynamic Force Taking into Account Parasitic Influences from Multicomponent Forces and Temperature Effects", Dynamic Calibration of Material Testing Machines (Guideline DKD-R 9-4), (2023) : 1-60
2. Gerber, S., Nitschke, A., Neumann, S., Kumme, R., Tegtmeier , F., Oliveira, R.S., Machado, R.R., Wozniak, M., Dizdar, H., Aydemir, B., Korhonen, J., Hiti, M. "Calibration Procedure for Testing Machine yo Close the Traceability Chain for Dynamic Forces Across a Frequency Range Of 0 Hz To 1000 Hz Including a Template Calibration Certificate Which Can Be Used for Forces in the Range of 1 N to 1 MN", Dynamic Calibration of Material Testing Machines (Guideline DKD-R 9-4), (2023) : 1-56
3. Sander, J., Kumme, R., Tegtmeier , F., Knott, A., Prato, A., Germak, A., Oliveira, R.S., Hiti, M., Dizdar, H., Aydemir, B., Vavre?ka, L., Korhonen, J. "Guidelines Detailing Recommendations and Standards for Force Calibration of Testing Machines Under Continuous Forces Taking into Account Parasitic Influences From Multicomponent Forces and Temperature Effects", ComTraForce, (2023) : 1-42
4. Knott, A., Sander, J., Kumme, R., Tegtmeier , F., Hiti, M., Vavre?ka, L., Fidelus, J., Prato, A., Germak, A., Dizdar, H., Aydemir, B., Korhonen, J., Oliveira, R.S. "Calibration Procedure for Testing Machines to Extend the Traceability Chain From Static to Continuous Forces Which Can Be Used for Forces in the Range of 1 N to 1 MN", ComTraForce, (2023) : 1-17
5. Knott, A., Aslantas, A., Arrhén, F., Averlant, P., Aydemir, B., Germak, A., Hiti, M., Kumme, R., Malengo, A., Martín, M.N.M., Roske, D., Vavre?ka, L. "Guidelines on the Uncertainty of Force Measurements", EURAMET e.V., (2022) : 48


  KİTAPTA BÖLÜM YAZARLIĞI
1. Aydemir, B. "Malzeme Test Makinalarının Hız Kalibrasyonu Ve Ölçüm Belirsizliğinin İncelenmesi",Y., H. (ed)., "Doğa ve Mühendislik Bilimlerinde Güncel Tartışmalar 8", Ankara : Bilgin Kültür Sanat Yayınları, (2023),19. (978-625-6925-21-2)
2. Aydemir, B. "Kuvvet Sensörlerinde Kullanılan Elektriksel Ölçme Yöntemleri", Bideci, A. (ed)., "Mühendislik Alanındaki Gelişmeler", İzmir : Duvar Yayınları, (2022), 75-109 (Bölüm 6). ( 978-625-8109-13-9)
3. Aydemir, B. "Plastiklerin ISO 527 Standardına Göre Çekme Özelliklerinin Belirlenmesi",Dr., D. (ed)., "Mühendislik Alanındaki Gelişmeler", İzmir : Duvar Yayınları, (2022),111. (978-625-8109-13-9)


  DİĞER İNDEKSLERDE TARANAN MAKALELER
1. Akbas, F., Aydemir, B. "Kapasitif Etki Prensipli Kuvvet Ölçme Cihazların Yapısının, Türlerinin ve Kullanım Alanlarının İncelenmesi", International Journal of Industrial Development Research, 1:1 (2022) : 13-24
2. Durmus, H.O., Aydemir, B., Ari, E., Karaboce, B. "Investigation of Effects of Tungsten on Acoustic Impedance by Calculating Sound Velocities from Elastic Modulus Approach", Euroasia Journal of Mathematics, Engineering, Natural & Medical Sciences, 8:17 (2021) : 150-159
3. Durgut, Y., Ganioglu, o., Aydemir, B., Turk, A., Yilmaz, R., Hamarat, A., Bagci, e. "Improvement of dynamic pressure standard for calibration of dynamic pressure transducers (19th International Congress of Metrology)", EDP Sciences, -:https://doi.org/10.1051/metrology/201927009 (2019) : 27009
4. Durgut, Y., Yilmaz, R., Aydemir, B., Bagci, E. "Dinamik Basınç Sensörlerinin Kalibrasyonu İçin Referans Standard Geliştirilmesi", Academic Perspective Procedia, 2:3 (2019) : 696-703
5. Dizdar, H., Aydemir, B., Vatan, C. "Differences of Latest Versions of ISO 6892-1 and ASTM E8 Tensile Testing Standards", Biological and Chemical Research, 5:1 (2018) : 11-22
6. Durgut, Y., Bilgic, E., Aksahin, E., Fank, S., Bagci, E., Ince, A.T., Aydemir, B. "Uncertaint Evaluation for Dynamic Pressure Measurements", EJOSAT : European Journal of Science and Technology, -:8 (2016) : 46-49
7. Gherasimov, A., Fank, S., Aydemir, B. "Interlaboratory Comparison Between TUBITAK UME Turkey and INM Romania in the Field of Force Measurement", Metrologie, -:3 (2009) : 44-50


  RAPOR
1. Kacar, B., Aydemir, B., Dizdar, H., Vatan, C., Kuru, U. "Evaluation of Alignment Data to ISO 23788 and ASTM E1012", Gebze : TUBITAK National Metrology Institute (TUBITAK UME), 2021.
2. Knott, A., Dizdar, H., Aydemir, B. "Report of Review of Testing Machine Facilities", Braunschweig : Euromet, 2021.
3. Kacar, B., Aydemir, B., Dizdar, H., Vatan, C. "Similarities/Differences between ASTM E1012-19 and ISO 23788:2012", Braunschweig : Euromet, 2021.